What's new
British Ordnance Collectors Network

This is a sample guest message. Register a free account today to become a member! Once signed in, you'll be able to participate on this site by adding your own topics and posts, as well as connect with other members through your own private inbox!

ZUS 40 (Anti withdrawal device 40) Germany WW2

pzgr40

Well-Known Member
Cutaway model of a ZUS (Zunder Sperre / Anti withdrawal device) 40. This device was used in German WW2 aircraft bombs as an additional antiwithdrawal device, to be used under a normal fuze. In contrast to the other electrical fuzes mentioned before, this is a fully mechanical device.

Description: the main body (1) is a zamac (Zinc/Alu/Mag/Cupper, ofter used for carburator cast parts) cast housing. It has three slots 3 mm wide at 120 degrees each. Each slot contains a knife edged plate (3) pushed outward by a spring (7) in one of the three slider pieces (8 ). These knives enshure that once the ZUS40 is placed in the fuze pocket it cannot be pulled out , i.e. the harder you'll try to pull it out ,the more the knives will "dig in" the fuze pocket wall. A hole is drilled between two slots in the lower part of the body. It houses a spring loaded cylinder shaped slider piece (4) with a perpendicular detent arm attached. The end of the slider piece(4) has a slotted insert piece (15), in which the firing pin (6) rests. The Slider piece however cannot move as it is locked in position by a spring loaded arming pin (9) which is held in place by a ball (10). The ball is lockd up between the arming pin and the base plate (2). The base plate (2) is connected to the upper body with two screws. It is also internally threaded to receive the Kz.Zdlg.C/98.
Functioning of the fuze: As a fuze is placed over the ZUS40 , the detent arm , connected to the slider piece (4) is pushed outward by the gaine of the upper fuze. At impact ,the ball (10) is thrown outward by inertia, releasing the arming pin. The fuze is now armed. As soon as attempts are made to remove the upper fuze, and the gaine of the upper fuze is nearly removed from the upper body of the ZUS40 ,the detent arm and the connected slider piece are free to move inward.The firing pin (6) is now free to move down into the firing cap (11). The flame travels into the booster through four small holes (12) in the baseplate (2).It ignites the Kz Zdlg.(Kurze Zundladung / short booster) C/98 (14) The Booster is made of an aluminium can, containing 17 grams of Np (Nitropenta)10 (pink). In top of the fuze a sprengkapsel (detonator) 38 (13) is placed. A leather washer with a celluloid disc is placed above the detonator, the aluminium can is rimmed over the leather washer to close the booster. The booster is placed in the gaine (15), which is screwed in the base (2) of the fuze. It cannot be observed from the outside if a bomb has a ZUS40 installed or not.
ZUS40__numbers_.JPG
 
Picture showing the three models of Zus 40
_8_s1_fuzes_and_Zus40_variations_003.jpg
 
Last edited by a moderator:
B) Oh man alive!,do i like those!
FM,You have only posted to tease me as i blagged that type 79A at Leeds!;)

pzgr40,Im sorry i missed your pictures and excellent write-up.:blush:

thank you both gents for info on these.
cheers and best


waff
 
I think one could generally say most SC and SD bombs of 50 kg or higher. The depending factor is the depth of the fuze well in the side of the bomb body. It cannot be used in special bombs like fhotoflash, smoke or cluster, only in High explosive types
Regarding the fuze type combination; It can only be used with bomb fuzes who use the Kz Zdlg.(Kurze Zundladung / short booster) C/98 at the base of the fuze.
Regards DJH
 
Last edited:
not a 50kg, there is not enough room

I think one could generally say most SC and SD bombs of 50 kg or higher. The depending factor is the depth of the fuze well in the side of the bomb body. It cannot be used in special bombs like fhotoflash, smoke or cluster, only in High explosive types
Regarding the fuze type combination; It can only be used with bomb fuzes who use the Kz Zdlg.(Kurze Zundladung / short booster) C/98 at the base of the fuze.
Regards DJH
 
The Zus40 was also usually used with the type 17 clockwork fuze. It was designed as a booby trap device to explode when the bombs were being defused. Impact fuzes were designed to explode when they hit the ground, so there was little point in putting these devices under an impact fuze. Used mainly on 250kg bombs in conjunction with the type 17 and type 50 fuzes - they could however be fitted to anything above this as well.

Kev
 
Top